Image is for illustrative purposes only. Please refer to product description.
- Manufacturer
- Siemens
- Manufacturer part number
- 6ES7132-6BH01-0BA0
- Product family
- SIMATIC ET 200SP Distributed I/O
- Category
- PLCs and I/O › Digital I/O modules
- Technical datasheet
- Data sheet
Specifications
| Attribute | Value |
|---|---|
| Type | Digital output module |
| Manufacturer lifecycle | Active |
| Product type designation | DQ 16x24VDC/0.5 ST |
| HW functional status | from FS21 |
| Firmware version | V0.0 |
| Firmware version / FW update possible | No |
| usable BaseUnits | BU type A0 |
| Color code for module-specific color-coded label | CC00 |
| Product function / I&M data | Yes; I&M0 to I&M3 |
| Product function / Isochronous mode | No |
| Engineering with / STEP 7 TIA Portal configurable/integrated from version | STEP 7 TIA V14 with HSP0222 / integrated as of TIA V15 |
| Engineering with / STEP 7 configurable/integrated from version | V5.5 SP3 with HSP0230 V7.0 / integrated as of V5.6 SP1 |
| Engineering with / PCS 7 configurable/integrated from version | V8.1 SP1 |
| Engineering with / PROFIBUS from GSD version/GSD revision | One GSD file each, Revision 3 and 5 and higher |
| Engineering with / PROFINET from GSD version/GSD revision | GSDML V2.3 |
Show all 103 specificationsShow fewer specifications
| Operating mode / DQ | Yes |
|---|---|
| Operating mode / DQ with energy-saving function | No |
| Operating mode / PWM | No |
| Operating mode / Oversampling | No |
| Operating mode / MSO | No |
| Supply voltage / Rated value (DC) | 24 V |
| Supply voltage / permissible range, lower limit (DC) | 19.2 V |
| Supply voltage / permissible range, upper limit (DC) | 28.8 V |
| Supply voltage / Reverse polarity protection | Yes |
| Input current / Current consumption, max. | 30 mA; without load |
| Output voltage / Rated value (DC) | 24 V |
| Power loss, typ. | 1 W |
| Address space per module / Address space per module, max. | 2 byte; + 2 bytes for QI information |
| Hardware configuration / Automatic encoding | Yes |
| Automatic encoding / Mechanical coding element | Yes |
| Automatic encoding / Type of mechanical coding element | Type A |
| Selection of BaseUnit for connection variants / 1-wire connection | BU type A0 |
| Selection of BaseUnit for connection variants / 2-wire connection | BU type A0 with AUX terminals or potential distributor module |
| Selection of BaseUnit for connection variants / 3-wire connection | BU type A0 with AUX terminals or potential distributor module |
| Type of digital output | Source output (PNP, current-sourcing) |
| Number of digital outputs | 16 |
| Digital outputs / Current-sinking | No |
| Digital outputs / Current-sourcing | Yes |
| Digital outputs, parameterizable | Yes |
| Digital outputs / output type acc. to IEC 61131, type 0.5 | Yes |
| Digital outputs / Short-circuit protection | Yes; Electronic |
| Short-circuit protection / Response threshold, typ. | 1 A; 0.7 to 1.3 A |
| Digital outputs / Open-circuit detection | Yes |
| Digital outputs / Limitation of inductive shutdown voltage to | Typ. L+ (-50 V) |
| Controlling a digital input | Yes |
| Switching capacity of the outputs / with resistive load, max. | 0.5 A |
| Switching capacity of the outputs / with inductive load, max. | 0.5 A |
| Switching capacity of the outputs / on lamp load, max. | 5 W |
| Load resistance range / lower limit | 48 Ω |
| Load resistance range / upper limit | 12 kΩ |
| Output current / for signal "1" rated value | 0.5 A |
| Output current / for signal "1" permissible range, max. | 0.5 A |
| Output current / for signal "0" residual current, max. | 0.1 mA |
| Output delay with resistive load / "0" to "1", typ. | 50 µs |
| Output delay with resistive load / "1" to "0", typ. | 100 µs |
| Parallel switching of two outputs / for uprating | No |
| Parallel switching of two outputs / for redundant control of a load | Yes |
| Switching frequency / with resistive load, max. | 100 Hz |
| Switching frequency / with inductive load, max. | 0.1 Hz; higher frequencies are possible, see Equipment Manual "Maximum permitted switching frequency of inductive loads" |
| Switching frequency / on lamp load, max. | 10 Hz |
| Total current of the outputs / Current per channel, max. | 0.5 A |
| Total current of the outputs / Current per module, max. | 8 A; see Equipment Manual "Derating curve" |
| Total current of the outputs (per module) / horizontal installation / up to 40 °C, max. | 8 A |
| Total current of the outputs (per module) / horizontal installation / up to 50 °C, max. | 6 A |
| Total current of the outputs (per module) / horizontal installation / up to 60 °C, max. | 4 A |
| Total current of the outputs (per module) / vertical installation / up to 30 °C, max. | 8 A |
| Total current of the outputs (per module) / vertical installation / up to 40 °C, max. | 6 A |
| Total current of the outputs (per module) / vertical installation / up to 50 °C, max. | 4 A |
| Cable length / shielded, max. | 1 000 m |
| Cable length / unshielded, max. | 600 m |
| Interrupts/diagnostics/status information / Diagnostics function | Yes |
| Interrupts/diagnostics/status information / Substitute values connectable | Yes |
| Alarms / Diagnostic alarm | Yes |
| Diagnoses / Monitoring the supply voltage | Yes |
| Diagnoses / Wire break | Yes; module-wise |
| Diagnoses / Short-circuit to ground | Yes; module-wise |
| Diagnoses / Short-circuit to L+ | Yes; module-wise |
| Diagnoses / Group error | Yes |
| Diagnostics indication LED / Monitoring of the supply voltage (PWR-LED) | Yes; green PWR LED |
| Diagnostics indication LED / Channel status display | Yes; green LED |
| Diagnostics indication LED / for channel diagnostics | No |
| Diagnostics indication LED / for module diagnostics | Yes; green/red DIAG LED |
| Potential separation channels / between the channels | No |
| Potential separation channels / between the channels and backplane bus | Yes |
| Potential separation channels / Between the channels and load voltage L+ | No |
| Isolation tested with | 707 V DC (type test) |
| Standards, approvals, certificates / Suitable for safety functions | No |
| Standards, approvals, certificates / Suitable for safety-related tripping of standard modules | No |
| Ecological footprint / environmental product declaration | Yes |
| Ecological footprint / Global warming potential / global warming potential, (total) [CO2 eq] | 29.3 kg |
| Ecological footprint / Global warming potential / global warming potential, (during production) [CO2 eq] | 3.98 kg |
| Ecological footprint / Global warming potential / global warming potential, (during operation) [CO2 eq] | 25.6 kg |
| Ecological footprint / Global warming potential / global warming potential, (after end of life cycle) [CO2 eq] | -0.245 kg |
| Ambient temperature during operation / horizontal installation, min. | -30 °C; < 0 °C as of FS03 |
| Ambient temperature during operation / horizontal installation, max. | 60 °C |
| Ambient temperature during operation / vertical installation, min. | -30 °C; < 0 °C as of FS03 |
| Ambient temperature during operation / vertical installation, max. | 50 °C |
| Altitude during operation relating to sea level / Installation altitude above sea level, max. | 5 000 m; restrictions for installation altitudes > 2 000 m, see ET 200SP system manual |
| Absolute humidity / dew point, min. | -60 °C; suitable for dry room applications |
| Width | 15 mm |
| Height | 73 mm |
| Depth | 58 mm |
| Weight, approx. | 30 g |
Description
The Siemens 6ES7132-6BH01-0BA0 is the ET 200SP DQ 16x24VDC/0.5A ST digital output module: 16 source (PNP) outputs at 24 V DC and 0.5 A. Siemens's data sheet gives electronic short-circuit protection, substitute value output and diagnostics for short circuit, wire break and supply voltage; it fits BaseUnits of type A0. SiePortal lists it as an active product.
Application: Digital output module
Used with: ET 200SP BaseUnits of type A0
What is the 6ES7132-6BH01-0BA0 used for?
It switches relays, valves and indicator lamps from an ET 200SP station, 16 per module.
Key features
- 16 digital outputs, 24 V DC, 0.5 A each
- Source output (PNP)
- Electronic short-circuit protection
- Diagnostics: short circuit to L+ and ground, wire break, supply voltage
- Fits BaseUnit type A0, colour code CC00
Documents and Resources
Associated Products
| Image | Product | Description | Stock | View | Add to RFQ |
|---|---|---|---|---|---|
 | 6ES7155-6AU01-0CN0Siemens | IM 155-6 PN/2 High Feature interface module | In stock | View | |
 | 6ES7193-6AR00-0AA0Siemens | BusAdapter BA 2xRJ45 | In stock | View | |
 | 6ES7193-6BP00-0DA0Siemens | BaseUnit BU15-P16+A0+2D, new load group | In stock | View | |
 | 6ES7193-6BP00-0BA0Siemens | BaseUnit BU15-P16+A0+2B, bridged to the left | In stock | View | |
 | 6ES7131-6BH01-0BA0Siemens | DI 16x24VDC ST digital input module | In stock | View |
Product Questions
Is the 6ES7132-6BH01-0BA0 discontinued?
No. Its manufacturer lifecycle status is Active.
Can another Siemens SIMATIC ET 200SP part replace it?
Potential replacements must be checked against the required ratings, dimensions and connections. Sharing a family name does not establish interchangeability.
Do you ship worldwide?
Yes. TimControls ships worldwide. Parts usually ship within 3 to 7 working days of order confirmation, and the exact lead time and shipping options are stated on your quote. Include your delivery country and postal code when you ask for a quote.
Latest news
TimControls is an independent distributor. Manufacturer names and logos are the property of their respective owners and identify products we source; they do not imply manufacturer authorization or affiliation.