6ES7153-2BA10-0XB0

Siemens IM 153-2 High Feature interface module for ET 200M, up to 12 modules

Read from the product label

Maker: Siemens
Part no.: 6ES7153-2BA10-0XB0
Serial / rev.: as printed on your unit

Illustration of the unit type, not a photo of this part.

Delivery options

Siemens SIMATIC DP IM 153-2 High Feature interface module for ET 200M: up to 12 S7-300 modules, redundancy capable, time stamping, isochronous mode, 24 V DC.

Manufacturer: Siemens
Manufacturer part no.: 6ES7153-2BA10-0XB0
Product family: SIMATIC ET 200M Remote I/O
Type: Interface module
Lifecycle: Discontinued: product cancellation (Siemens SiePortal), spare part only
OEM successor: Not stated
Technical datasheet: Data sheet

Technical specifications

Manufacturer: Siemens
Manufacturer part no.: 6ES7153-2BA10-0XB0
Type: Interface module
Application: PROFIBUS DP interface for ET 200M
Used with: ET 200M station on PROFIBUS DP
Product type designation: IM 153-2 DP HF
Firmware version: V6.0.0
Vendor identification (VendorID): 801Eh
Supply voltage / Rated value (DC): 24 V
Supply voltage / permissible range, lower limit (DC): 20.4 V
Supply voltage / permissible range, upper limit (DC): 28.8 V
external protection for power supply lines (recommendation): 2,5 A
Mains buffering / Mains/voltage failure stored energy time: 5 ms
Input current / Current consumption, max.: 650 mA; with 24 V DC supply
Input current / Inrush current, typ.: 3 A
Input current / I²t: 0.1 A²·s
Output current / for backplane bus (5 V DC), max.: 1.5 A
Power loss, typ.: 5.5 W
Address space per module / Inputs: 244 byte
Address space per module / Outputs: 244 byte
Hardware configuration / number of modules per DP device interface, max.: 12
Time stamp / Accuracy: 1 ms; 1 ms at up to 8 modules; 10 ms at up to 12 modules
Time stamp / Number of message buffers: 15
Time stamp / Messages per message buffer: 20
Time stamp / Number of stampable digital inputs, max.: 128; Max. 128 signals/station; max. 32 signals/slot
Time format: RFC 1119
Time resolution: 0.466 ns
Time interval for transmitting the message buffer if a message is present: 1 000 ms
Time stamp on signal change: rising / falling edge as signal entering or exiting
Interfaces / Transmission procedure: RS 485

Show all 57 specifications

Interfaces / Transmission rate, max.: 12 Mbit/s
1. Interface / automatic detection of transmission rate: Yes
Interface types / Output current of the interface, max.: 70 mA
Interface types / Design of the connection: 9-pin sub D socket
PROFIBUS DP device / GSD file: SI05801E.GSG
PROFIBUS DP device / automatic baud rate search: Yes
Protocols / Bus protocol/transmission protocol: PROFIBUS DP to EN 50170
Protocols (Ethernet) / TCP/IP: No
PROFIBUS DP / Number of node addresses, max.: 1 to 125 permitted
PROFIBUS DP / Services / SYNC capability: Yes
PROFIBUS DP / Services / FREEZE capability: Yes
PROFIBUS DP / Services / Direct data exchange (slave-to-slave communication): Yes; as publisher with all IO, as subscriber with F-IO only
Potential separation exists: Yes
Isolation tested with: Isolation voltage 500 V
IP degree of protection: IP20
Ambient temperature during operation / min.: 0 °C
Ambient temperature during operation / max.: 60 °C
Ambient temperature during operation / horizontal installation, min.: 0 °C
Ambient temperature during operation / horizontal installation, max.: 60 °C
Ambient temperature during operation / vertical installation, min.: 0 °C
Ambient temperature during operation / vertical installation, max.: 40 °C
Altitude during operation relating to sea level / Installation altitude above sea level, max.: 3 000 m
Configuration software / STEP 7: Yes; STEP 7 / COM PROFIBUS / non-Siemens tools via GSD file
Width: 40 mm
Height: 125 mm
Depth: 117 mm
Weight, approx.: 360 g

Technical documents (1)

Siemens data sheet 6ES7153-2BA10-0XB0

Key features

Head module of an ET 200M station on PROFIBUS DP
Up to 12 S7-300 modules per station
Redundancy capable
Time stamping of up to 128 digital inputs, 1 ms accuracy with up to 8 modules
Isochronous mode
Discontinued by Siemens on 1 October 2025; spare part only

About the Siemens 6ES7153-2BA10-0XB0

The Siemens 6ES7153-2BA10-0XB0 is the IM 153-2 High Feature interface module for ET 200M. Siemens describes it as redundancy capable, with time stamping and isochronous mode, for up to 12 S7-300 modules. Its data sheet gives time stamping of up to 128 digital inputs per station, with 1 ms accuracy at up to 8 modules and 10 ms at up to 12, and a 24 V DC supply. Siemens's data sheet marks it as a spare part. Siemens's route forward is the ET 200MP I/O system.

What is the 6ES7153-2BA10-0XB0 used for?

It heads ET 200M stations where more than a standard IM 153-1 is needed: redundant PROFIBUS links, time-stamped digital signals, and isochronous operation.

Lifecycle and successor

Discontinued: product cancellation (Siemens SiePortal), spare part only.

Before you order

What to photograph or confirm so the right unit is quoted.

Check the order number on the module and whether the station runs with two interface modules (redundancy). Note the PROFIBUS address set on it.

Alternatives for 6ES7153-2BA10-0XB0

The manufacturer’s named successor and other parts in the same family. None is a drop-in replacement without checking wiring, I/O and configuration for your installation.

Product	Manufacturer	Type	Lifecycle	Relationship	Qty Available	Price	Action
Siemens 6ES7153-1AA03-0XB0IM 153-1 interface module for ET 200M, up to 8 modules	Siemens	Interface module	Discontinued: product cancellation (Siemens SiePortal), spare part only	Same family	On Request	On request	View ›

You may also be interested in

TIMC is an independent distributor. Manufacturer names and logos are the property of their respective owners and identify products we source; they do not imply manufacturer authorisation or affiliation.

Need Siemens 6ES7153-2BA10-0XB0? Send us the details.

Request a Quote